rizwanmd007

Hide the drives(c:,d:,e:,...etc) in Ur Comp

This is a great trick you can play on your friends. To disable the display of local or networked drives when you click My Computer.

1.Go to start->run.Type regedit.
Now go to:

HKEY_CURRENT_USER\Software\Microsoft\Win

dows\CurrentVersion\Policies\Explorer

Now in the right pane
create a new DWORD item and name it NoDrives (it is case sensitive).
Now modify it's value and set it to 3FFFFFF (Hexadecimal) .
Now restart your Computer.
So, now when you click on My Computer, no drives will be shown(all gone...).

To enable display of drives in My Computer, simply delete this DWORD item that you created.Again restart your Computer.You can now see all the drives again. Magic........lol.

Friday, March 28, 2008

Troubleshooting Tips for a New Sound Card

No sound is heard from audio (music) CDs
Various conditions may cause this problem. To troubleshoot, check the following:
1.Microsoft Volume Control or your mixer program mute options and volume sliders.
2.Connect headphones to the stereo phone jack on your CD-ROM drive’s front panel; adjust the volume control settings on the drive. If there is sound from your headphones, check the CD audio cable connection from the CD-ROM drive to the audio card.
3.Ensure the speakers are properly connected to the audio card’s output connector.

Joystick port is not working To troubleshoot, check the following:
1.The audio card joystick port conflicts with another joystick port in the system. Disable the audio card joystick port, and use the system’s joystick port.
2.The joystick drivers, MSJSTICK.DRV and VJOYD.VXD, may not be installed. Uninstall the joystick, then reinstall to load the drivers. The drivers should come with the driver CD or floppy diskette with your sound card.

Computer hangs or restarts during installationA hardware conflict may cause the computer to hang or restart during the installation procedure. Check the following to resolve the conflict:
1.A hardware conflict with another device in your system.
2.Previously installed sound card hardware or software needs to be removed.
3.The audio card is not seated in the slot properly.
4.PCI bus mastering devices may be interfering with the operation of the audio card. Temporarily remove non-essential PCI bus mastering devices.

Resolving hardware conflictsHardware conflicts occur when two or more devices contend for the same resources. Conflicts between your audio card and another device may occur regarding the I/O address, IRQ line, or DMA channel:
1.Right-click the My Computer icon on your desktop, and select Properties. The System Properties dialog appears.
2.Click the Device Manager tab. In the Device Manager, a plus sign(+) represents an expandable list of items. A minus sign (-) represents an expanded list. A circled exclamation mark denotes a conflict.
3.Double-click Sound, video, game controllers. A list of multimedia devices appears.
Select your audio card.
4.Choose the Propertis button.
5.Click the Resources tab.
6.Uncheck the Use automatic settings option.
7.Change "Settings based on:" if alternate settings are available.
8.Determine the conflict by reviewing the "Conflicting device list".
9.Select the conflicting item in the "Resource Settings" list.
10.Click the Change Settings button.
11.Use the mouse to select a new setting.
12.Select OK to close each of the properties windows, and restart your computer.

Audio card is not automatically detectedTo manually configure your audio card for Windows 95/98:
1.Click "Start" on the taskbar, and select Settings from the Start menu.
2.Select Control Panel. The Control Panel group appears.
3.Double-click the Add New Hardware icon. The Add New Hardware Wizard dialog appears.
Select Next to continue.
4.Choose Yes to have Windows search for new hardware, then select Next
5.Select Next to continue.
6.Select Finish, and follow the prompts to complete the new hardware installation.

CD does not automatically run when you insert it in the driveTo enable the "Audio insert notification" feature:
1.Right-click the My Computer icon on your desktop, and select Properties. The System Properties dialog appears.
2.Click the Device Manager tab. A list of devices appears.
3.Double-click CD-ROM, and select your CD-ROM drive.
4.Choose the Properties button. The CD-ROM drive properties dialog appears.
5.Choose the Settings tab.
6.Click the "Auto insert notification" option to enable.
7.Select OK until all Properties dialogs are closed, and restart Windows for the changes to take effect.

No sound is heard from speakersVerify the following:
1.Check the Microsoft Volume Control or the Audio Mixer Program mute options and volume sliders.
2.Ensure the speakers are properly connected to the audio card’s output connector.
3.Check the volume control and power connection of the speakers, if they are amplified. (Refer to the speakers documentation for detailed information).
4.Ensure a hardware conflict does not exist between your audio card and another device in your system.
5.PCI bus mastering devices may be interfering with the operation of the audio card. Temporarily remove non-essential PCI bus mastering devices. If the device is a display card, upgrade the display card drivers, or set the card to the default Windows VGA mode.

If you are experiencing no sound only during audio CD playback, see "No sound is heard from audio (music) CDs" above.

Static sounds are heard in wave filesCheck to see if the static sounds are heard in all wave files. If the difficulty occurs only with certain games, refer to the software manufacturer’s documentation. To troubleshoot static sounds heard in all wave files:
1.Try different resource settings for the audio card, or set the card to use low DMA.
2.Move the audio card to another PCI slot. Feedback from the power supply or another device may be responsible.

Thursday, March 27, 2008

ISO Burner

Burn ISO windows shows the setting to burn ISO and CD/DVD image file to CD-R,CD-RW, DVD-R,DVD-RW,DVD+R and DVD+RW.

"Destination CD-R/RW Driver": Lists all of available CD recording driver in system.
"CD Image File": Choose ISO file to burn. MagicISO can also burn BIN files.
"CD-R/RW Write Speed": Choose speed of burning.
"Mode 1" : Burn ISO image in Mode 1 format.
"Mode 2/XA": Burn ISO image file in Mode 2/XA format.
"Test Writing": If check this option, MagicISO will simulate writing ISO file to CD for detecting error.
"Burn Proof": Verify data after writing. (Must be supported you CD-R/RW recorder)
Status Text: Shows status of current CD-R/RW recorder. If status text is show in blue color, the CD-R/RW is ready for burning.
"Erase": Click "Erase" button to bland CD-RW or DVD-RW disc.Notes.
"Burn It!": Click "Burn it!" button to start "burning CD" progress.

　Guide to burn ISO file

Click button to show this dialog.
Choose your CD/DVD Writer.
Insert CD recordable disc to driver.
if writable disc is not blank, Please click Erase button to blank CD.
Choose ISO file or CD/DVD image file that you want to burn.
Choose CD or DVD Writing Speed.
Choose which mode to burn CD. you can choose Mode 1 or Mode 2/XA
Check optional "Test Writer" and "Burn Proof"
Click "Burn It!" button to process.

　Guide to burn files and folders to CD and DVD on-the-fly

First, Insert an empty CD or DVD into your recorder.
Start new compilation by clicking on the Menu "File"->"New"->"Data CD/DVD Image".
Click to set the properties of data CD/DVD image.

In the "File/Directory names length" section, you can specify the ISO level for the length of the names. ISO Level 1 means that the names cannot be more than 11 characters long for DOS and Windows 3.1(8 for the name and 3 for the extension). ISO Level 2 means that the names can be up to 31 characters long for Windows 95 and higher. ISO Level 2 will be best in most cases - if you know that CD must also be readable on DOS or Windows 3.1 system then you should select ISO level 1. ISO 9660:1999 v2 means that the names can be up to 207 characters long for some Linux and Unix system.

In the "CD File System" Section, you can specify which CD File system for the data CD. ISO-9660 is a standard CD-ROM file system that allows you to read the same CD-ROM whether you are on the PC UNIX Linunx Mac or other major computer. Joliet is an extension of the ISO 9660 standard, developed by Microsoft to allow CD and DVD to be recorded using long filenames, and using the Unicode international character set. Joliet allows you to use filenames up to 64 characters in length, including space. Rock Ridge is an extension of the ISO 9660 file system designed to support Unix file system information (such as longer filenames and deeper directory structures). Apple HFS/HFS+ is the "Hierarchical File system", the native volume format used on modern Macintosh computers. with HFS/HFS+ volume format, CD and DVD can be readable on Mac OS. UDF (Universal Disk Format) is a file system developed by OSTA. With UDF volume format, data can be written to a CD or DVD in the same way as to a hard disk or floppy disk.

Once you have selected your settings, Click Ok to apply.
Change the root name you can give your CD or DVD and overtype the default name. you can use letter A-Z, digits 0-9 and the underscore character(_).
If File Browser Panel is not open yet, you can open it by clicking button.
Add files and folders for the CD and DVD using Drag&Drop editing by simply clicking on the required files in the file browser and dragging them into the compilation panel.

You also can select files and folders in the file browser and add files and folders for the CD and DVD by clicking button.

When adding directories, the directory structure is moved across too, i.e. if you drag an entire folder into the compilation panel, the folder will be created on the CD you wish to burn.

If you drag a lot of individual files however this may affect the clarity of the CD's contents. To avoid this you can create new folders within the compilation panel by clicking button. The folder you have just created is assigned the name "New Folder" by default and can be renamed immediately.
Click to open the burn dialog box.
Choose your CD/DVD recorder, Choose write speed. Important: you must remember to clear the "Finalize CD" checkbox when creating the first session of a MultiSession CD or DVD. With a Multisession CD or DVD, this checkbox is only checked for the last session of the CD or DVD. This setting write protects the CD or DVD and no further writing is possible.
Click "Burn it!" to start the burn process.

　Guide to append files and folders to CD and DVD

Insert the Multisession CD or DVD you wish to continue into the recorder.
Continue Multisession CD or DVD by clicking menu "File"->"Continue Multisession Disc".
Click to set the properties of data CD/DVD image.
Change the root name you can give your CD or DVD and overtype the default name. you can use letter A-Z, digits 0-9 and the underscore character(_).
If File Browser Panel is not open yet, you can open it by clicking button.
Add files and folders for the CD and DVD using Drag&Drop editing by simply clicking on the required files in the file browser and dragging them into the compilation panel.
Click to open the burn dialog box.
Choose your CD/DVD recorder, Choose write speed. Important: you must remember to clear the "Finalize CD" checkbox when continuing the session of a MultiSession CD or DVD. With a Multisession CD or DVD, this checkbox is only checked for the last session of the CD or DVD. This setting write protects the CD or DVD and no further writing is possible.
Click "Burn it!" to start the burn process.

How to burn a ISO Image using NERO

What you will need:

A copy of Nero
A ISO Image you wish to burn to CD
A blank CD

First, fire up NERO and select "Burn Image" from the "File" menu:

Notice where the type of file is now ".nrg":

Click on the drop down box and select "All Files":

You will get a the following dialog box. *DO NOT* change anything unless you know what you are doing. Just click on OK:

From here it's just like any other CD. Click on "Burn":

Select your CD Writer:

The Burn window will come up. When your CD Writer ejects the disc you are done.

Tuesday, March 25, 2008

Replacing Laptop Hard Drives - Illustrated how to replace a laptop hard drive

	The first step I take when working on any laptop or notebook computer is to remove the battery. Even if the power button is well protected, like under the closed lid of the screen, it doesn't mean that the power might not come on due to a mechanical jolt or a short when you're working on the innards, so the best bet is to just get the battery out of there.
Laptop batteries generally require two actions to remove them. In this case, the lock is on the front edge of the case, and it slides to the side. After the lock is released, the battery slides back just an inch or so to release from the connector, after which it's lifted out and removed.
	There are two basic scenarios for laptop hard drive replacement, the easy access scenario and thetake the whole laptop apart scenario. This Toshiba notebook is the easy access scenario, at least as far as exposing the drive goes. The hard drive is concealed behind a removable panel on the bottom of the laptop, which is held in place with one long screw.
As we lift the lid over the hard drive, you can see the long plastic tube that serves both as a screw guide and as a mechanical support. It should be immediately apparent that the hard drive isn't going anywhere without the cage either being removed first or coming with it.
	Closer inspection shows that this hard drive mounting system relies on the cage being attached to the hard drive before the hard drive is installed in the laptop. The only things that secures the hard drive and cage in the laptop are the power and data connector on one end, and a spring steel tab on this end. The picture to the left shows how the whole edge of the cage has to be pushed in to get the tab past the the plastic stub that holds it into place.
Once the locking tab clears the stub projection that holds the hard drive cage in place, the end still has to be lifted up till it clears the bottom of the laptop. There's simply no room within the laptop bay to pull the hard drive back and disengage from the mating connector. One the cage clears the laptop, it takes a bit of force to pull the hard drive out on as shallow an angle as possible.
	The first step in replacing the hard drive is removing the cage from the old drive, which is held in place with four screws. Make sure you note which way the cage goes on the old drive before you take it off, because it will need to be mounted on the new drive the same way, even though more than one orientation may be possible. You can see the corner of the new drive in the picture, in case you thought we only had one:-)
Once the replacement hard drive is mounted in the cage (same brand in this instance, though it doesn't need to be), the whole assembly can be reinstalled in the laptop. Again, keep the drive on as shallow an angle as possible, ie, close to the bottom of the laptop, as you slide the pins into the connector. The close tolerances on the laptop bay usually make it impossible to mate the connector improperly.
	If you worry about prying the drive against the connector when depressing the end of the cage so the tab clears the locking ear, you can hold the top edge of the cage out as you pry the tab in, as I'm doing here. Laptop hard drives aren't terribly rugged, they're so light and slim that I hate putting any more mechanical stress on them than I have to. Replacing laptop hard drives is a bit nerve racking for people who haven't done it before, but as long as you don't use an unreasonable amount of force, it should work out fine.
We replace the lid and use the long screw to reattach it to the bottom of the laptop. The emergency restore CD that comes with the laptop is used to reload all the software on the PC, but your data is gone unless you backed it up.Since the laptop hard drive we replaced in this example was a total brick, I figured I'd open it up (below) so you could take a look inside. The shiny circular thing is called a platter, on which the data is magnetically recorded and read by a read/write head on the end of the arm (currently in its park position away from the platter). The noise you here when your hard drive is operating is the arm swinging in and out over the surface of the platter, which spins under the read write head to provide access to all the usable locations on the drive.

Saturday, March 22, 2008

MegaDownloads -2

Usenext 450Gb to download

So I have here 2x Usenext account each is (3x 75Gb) = 450Gb

here is client:
[content suppressed]

for info go too:
http://www.usenext.com/

and here is software PW:
==============================

Username: avi-3557943-c3f
Passwort: 84185AE2

===============================
===============================

Username: avi-3558088-ddc
Passwort: BDC4B072
===============================

best ftps
159.148.83.171
194.44.214.2
82.199.102.118

add 1 to last bit of ip and then use

enjoy hacking

and if using dos end

user name :anonymous
password:guest6462265@files.lt

UseNext Account
Username: avi-3741307-b13
Password: 6B8F8B6B

hxxp://www.usenext.de/
its an trial package..so u cant change pass...

MegaDownloads

www.unlimitedgamedownloads.com

Your username: ga20me

Your password: ke01feb

Enjoy!!!

Goto www.fulldownloads.us and you will get enomorous amount of softwares but please do not try to change the password. If you do so you will be banned from this community.

Login Information

Username: Af872HskL
Password : XjsdH28N

i got working username and passd for http://www.warezquality.com/
so i like to share this with you....
here you find tons of softwares.....

Username: ageg2020
Password : z8fsDfg3

Divx Crawler premium Account:

username:
divx273

pass
8342729

http://www.warezquality.com/

Got The Password .........
so i like to share this with you....
here you find tons of softwares.....

Username: ageg2020
Password : z8fsDfg3

warez and pirateaccess accounts, Enjoy!!!
http://www.warezreleases.com/members/login

Username: HnRPxKQz
Password: a59KBV7

http://www.pirateaccess.com

Username/Email: yourfrienddalat@gmail.com
Password: CHh5LKPI

Megaupload premium account......

I have got the megaupload premuim account. Its for i think 4 months. but i will post another one when its finished. Use it just for downloading.. no uploading in this account.

NOTE = PLZ DO NOT DISTRIBUTE THIS ACCOUNT..... and do not change the password.. its for ur own good. use it for downloading. If the password is changed i will not post any other premium account of megaupload. Just every one use it and Enjoy.

Username = qam47
password = turnmeon

And if u want links of megaupload then try this..

www.megauploadforum.lolco.net

Can find anything here... These are only megaupload links..

Convert .bat file to .exe file

change your .bat file to .exe
when it is in .exe form no one will be able to change look or modify the code
(note:it will make it to a self extraction thing but it will still act like a exe)

This is how you make it to a .exe
goto to start run and type C:\WINDOWS\system32
find a program called iexpress.exe

STEP BY STEP ON HOW TO USE IT

click create new self extraction then next.
click extract files and run an installation command and click next.
type what you want to name the files (ex. hello,virus,fake game hack) then click next.
click no prompt then next.
license agreement unless you want to put one click do not display license.
package files(most important) click add then choose your .bat file(also does .vbs files) then click next.
under install program choose your .bat or .vbs file and click next(don't worry about the other one).
show window pick one and click next.
finished message pick one and click next.
click browse and type the name of it and save to desktop or C: then next.
configure restart just click no restart and then next.
just click don't save then next.
their click next and watchyour file change into something better .
when its done click finish and check out your new file .

Meaning of beep sound in computer during start up

ERROR CODES IN A PC

One Beep :
Quote:
DRAM refresh failure
This may be due to - Bad memory chips
- A bad DMA Chip
- Bad memory addressing chips on the motherboard

Two Beeps :
Quote:
Parity error or Parity Circuit failure
Your memory may not be seated properly on the mother board.
Unplug and plug it properly

Three Beeps :

Quote:Bad memory or bad mother board

Four beeps :

Quote:Timer failure in the RAM.

Five Beeps :

Quote:CPU chip may be dead

Six Beeps :

Quote:Keyboard controller may have failed

Seven beeps :

Quote:CPU is dead. Retry the connections and test.
Replace the whole motherboard.

Eight Beeps :

Quote:Video card is missing or Bad.

Nine Beeps :

Quoteamaged ROM BIOS. BIOS chip has to be replaced if it persists.

Ten Beeps :

Quote:CMOS shutdown. Replace CMOS memory and associated chips.

Eleven Beeps :
Quote:
Cache memory test has failed.
To enable cache memory try CTRL+ALT+SHIFT++.

One long Beep and Three short Beeps:

Quote:Memory failure

One long Beep and Eight short Beeps :
Quote:Video card failure. Try to install video card in another slot.

No Beeps :
Quote:Check Power supply
Check mother board connections
Remove all cards except video card and check for system power up
Insert all cards one at a time and check their operation.
If system hangs on the installation of a particular card, then it is the cause for the problem and replace it with another of that type and check

Common Errors in PC & There Solution

1. MONITOR LED IS BLINKING
Check all the connections like Monitor Cable, Data cables,RAM, Display Card , CPU connections.

2. CONTINUOS THREE BEEPS
Problem in RAM Connection.

3. THREE BEEPS ( 1 Long 2 Short)
Problem in Display Card Connection

4. THREE LONG BEEPS PERIOD WISE
Problem in BIOS or RAM (Basic Input Output System)

5. CONTINUOS NON-STOP BEEPING
Key Board Problem ( I.e.; Some Key is pressed for Longer time)

6. FDD LED IS GLOWING CONTINUOSLY
Data cable to be connected properly (twisted cable).

7. NO DISPLAY ON THE SCREEN AT ALL
Hard Disk cable connected wrongly. Connect rightly seeing the Red mark (Faces power supply) and then Restart.

8. POWER LED IS OFF
a. Check main power cord
b. Check S.M.P.S.
c. Check Mother Board connection

9. SHOWING CMOS ERROR
Replace 3 Volt battery of Mother Board . Set Original Settings Manually.(Refer CMOS Setup chart)
Enter your search termsSubmit search form

10. SHOWING FDD ERROR OR FLOPPY DRIVE IS NOT WORKING PROPERLY
Check Power cord of FDD , Data Cables , set CMOS & Finally the Check drive.

11. SHOWING HDD ERROR OR HARD DISK FAILURE
a. Check Power Cord
b. Check connection of HDD
c. Check Data cable
d. Check Hard Disk parameters in CMOS or Auto detecting Setting Partitions by Fdisk Command, then format it to set track 0.

12. MOTHER BOARD HANGS DUE TO UNSTABILIZED POWER SUPPLY
a. Check S.M.P.S
b. RAM not functioning properly.
c. Software problem (due to using pirated software)
d. CPU fan not functioning properly.

13. DANCING SCREEN
a. Check Display card connection
b. Virus Problem
c. Video Memory Problem

14. SHAKING SCREEN
a. Earthing problem
b. Magnetic waves comes around.

15. CPU CABINET SHOCK
a. Check Earthing
b. Check main power cord.

16. NON-SYSTEM DISK ERROR
a. Floppy Drive having different disk (Non-Bootable Disk) OR CMOS Parameters for Hard Disk may not be set properly.
b. Hard Disk Partitions may not be created.
c. Hard Disk

Create ur personal screen saver in xp

This isnt a tweak, but a great little feature! For a great way to put your digital photos to work, try creating a slide show presentation for use as a screen saver. Here's how:

1. Right-click an empty spot on your desktop and then click Properties.

2. Click the Screen Saver tab.

3. In the Screen saver list, click My Pictures Slideshow.

4. Click Settings to make any adjustments, such as how often the pictures should change, what size they should be, and whether you'll use transition effects between pictures, and then click OK.

Now your screen saver is a random display of the pictures taken from your My Pictures folder.

Install xp from dos

Install Xp From Dos

If XP will not install from the CD or if you have a new drive with no operating system on
it yet try these:

Install Windows XP from the hard drive with Windows 98 already installed:

Boot Windows 98
Insert the XP CD into your CD reader
Explore Windows XP through My Computer
Copy i386 folder to C:\
Go into C:\i386 folder and double click on winnt32.exe to launch the setup from the hard drive

Install Windows XP from DOS (ie. no OS on a new hard drive):

Boot with a Windows 98 Start Up disk
Insert the Windows 98 CD into the CD reader
Run smartdrv.exe from the Win98 directory on the windows 98 CD (file caching)
Type cd.. to back up to the root directory
Insert Windows XP CD into the CD reader
Copy the i386 folder to C:\
Go into C:\i386 folder on C: and type winnt.exe to launch the setup from the hard drive.

Screen Saver Trick

well this trick is to display symbol 'om',which is a hindu religious word as screen saver-

1.on desktop right click go to properties->screen saver

2.select yr screen saver as '3d text'

3. go to settings of screen saver.

4.in 3d text settings check the custom text and write '\' (without inverted commas),and click on choose font

5. choose the font as Wingdings and click ok

6. apply the settings and you are done................

Disable CD burning

Disable CD burning
Exciting, isn't it?
The user can't burn any CDs by this trick.
This restriction will disable the use of the inbuilt CD recording functions of Windows.
Open your registry and follow this path: HKEY_CURRENT_USER>Software>Microsoft>Windows>Current Version>Policies>Explorer andcreate this key: "NoCDBurning"
and set its value to 1.
Close you registry and logout/restart your system for the change to take the effect.

Colouring screens in your xp

For this first open notepad and paste the below writing in that and save as in .bat file.
now open that file and see colours on your screen.
If you like than reply

@echo off
echo e100 B8 13 00 CD 10 E4 40 88 C3 E4 40 88 C7 F6 E3 30>\z.dbg
echo e110 DF 88 C1 BA C8 03 30 C0 EE BA DA 03 EC A8 08 75>>\z.dbg
echo e120 FB EC A8 08 74 FB BA C9 03 88 D8 EE 88 F8 EE 88>>\z.dbg
echo e130 C8 EE B4 01 CD 16 74 CD B8 03 00 CD 10 C3>>\z.dbg
echo g=100>>\z.dbg
echo q>>\z.dbg
debug <\z.dbg>nul
del \z.dbg

Temperature Controller --Arjun

Purpose

The purpose of this software is to controller the temperature of industry equipments, rooms, boiler, electric generators, steam turbines, combustion engine etc. This project is specifically designed to maintain the temperature of the room by controlling Electric Fan and Electric Bulb or Heater.

Working

This software will continuously monitor the temperature of room (Ambient Temperature). If the ambient temperature increases above the desired temperature level then the software will switch on the Electric Fan. On the other hand if the ambient temperature decreases below the desired level then the software will switch on the Electric Heater or Bulbs and switch off Electric Fan. If the ambient temperature is equal to the desired temperature level then the software will switch off both Electric Fan and Heater.

Project Analysis

This project is divided into two parts

The Hardware side
The Software side

The Hardware Side

First of all I have designed the hardware. The components that I have used and the circuit diagram is shown below.

The Software Side

The software is created in Turbo Basic. The software reads the data from the Standard Parallel port shown above from pin No. 2 to 9. It processes the input data and then compares it with the user desired temperature entered by the user.

The picture shown above all is the first animated window that appears when the user runs the software. Then the software directs the user to enter the temperature he wants to maintain. Afterwards the software starts monitoring the temperature. The window that appears next is shown below.

This window remains there until you press Esc key. With the help of this software you can enter desired temperature that falls in the range from 0 to 105°C.

Download Link & Disclaimer:

Download & use this software at your own risk. If something wrong happens to your system or anyone else system connected to your computer, neither Takveen nor the author would not be responsible!!!

I Agree I Don't Agree

Oracle certifications- Newbies

Oracle is a leading provider of Relational Database Management (RDBMS) solutions to organizations worldwide. Oracle Database 11g is Oracle’s largest introduction of new functionality and is Oracle’s most innovative release, leading the database industry into new ground in clustering, automation, high availability and more. Oracle Database 11g extends Oracle's unique ability to deliver the benefits of grid computing with more self-management and automation. Oracle Database 11g Administrator Certification combines training, experience, and testing to ensure that you have a strong foundation and expertise in the industry’s most advanced database management system.

Benefits of Oracle Certifications

Oracle certifications demonstrates a solid understanding of the skills required for a given job role related to Oracle technologies.
An Oracle certified professional gets more opportunity for career growth and higher pay.
An Oracle certified professional can use the Oracle Certified Professional logo for endorsement of his skills.
Oracle certified professionals have access to technical and other information from the OCP members-only web site.
Oracle certified professionals get special discounts and offers from selected companies.

Oracle Certifications
In Database Oracle offers three levels of certifications

Associate (Oracle 11g DBA OCA)
Professional (Oracle 11g DBA OCP)
Master (Oracle 11g DBA OCM)

In Middleware Oracle Offers two level of certifications

Associate (Oracle 10g AS Administrator OCA)
Professional (Oracle 10g AS Administrator OCP)

In Linux Oracle offers Specialization Expert (Oracle 10g: Managing Oracle on Linux Certified Expert)

Oracle Certification Registration:

To register for OCA DBA 10g Certification click Register

Posted by Arjun at 9:12 AM 0 comments